CCNA Routing and Switching interactive learning:
- More than 250 labs
- More than 5,000 hands-on tasks
Four Kinds of Labs:
- Skill Builders
- Subnetting Exercises
- Configuration Scenarios
- Troubleshooting Scenarios
The
CCNA Routing and Switching 200-125 Network Simulator is a single-user software package. It helps users develop and improve hands-on configuration and troubleshooting skills without the investment in expensive lab
hardware. This state-of-the-art, interactive simulation software enables you to practice your networking skills with more than 400 structured labs designed to help you learn by doing, the most effective method of learning.
Experience realistic network device responses as you perform each lab, which include detailed instructions, topology diagrams, critical-thinking questions, hints, and answers. Working through the labs, you will quickly become proficient with all the common Cisco IOS version 15 router and switch commands on the CCNA exam. Unlike other simulators on the market, the lab scenarios included in the CCNA R&S 200-125 Network Simulator are far more complex, challenging you to learn how to perform real-world network configuration and troubleshooting tasks.
Master the hands-on skills needed to succeed on the CCNA exam, including:
- Router and switch navigation and administration
- Ethernet LAN switches
- VLANs, trunking, and switch security
- Connected and static routes
- RIPv2 configuration and verification
- Access Control Lists (ACL)
- NAT, syslog, and NTP configuration
- IPv4 and IPv6 addressing and subnetting
- Network troubleshooting
- STP and VTP
- OSPF and EIGRP on IPv4 and IPv6
- External BGP
- Point-to-point WANs and private WANs
- HSRP
- Network management
Skill Builders:
These 250+ labs are narrowly focused, enabling you to practice your configuration skills on a single topic. Coverage includes:
- Router and switch CLI navigation
- Configuring IP addresses and DHCP
servers
- VLAN and trunking configuration
- Switch security
- STP, VTP, Portfast, and BPDU guard configuration
- Static and dynamic EtherChannel
- Serial configuration and authentication
- Connected, static, and default routes
- RIPv2, OSPF, and EIGRP configuration
- eBGP and MPLS
- ACL analysis and configuration
- NAT configuration
- Syslog, NTP, HSRP, GRE tunnels, SNMP, IP SLA, and SPAN
Subnetting Exercises:
These 80 labs help you to perform subnetting calculations quickly and accurately, a critical skill for success on the CCNA exam. Topics covered include:
- IPv4 and IPv6 subnet ID calculation
- IP address rejection
- IP route selection
- VLSM overlaps
- IPv6 EUI-64 calculation
- Selecting VLSM routes
Configuration Scenarios:
These 50+ labs are more broadly focused, combining multiple technologies into configuration scenarios that mimic real-world environments. These labs are longer and more complex, challenging you to put your configuration skills
to the test. Topics covered include:
- Network fundamentals and administration
- IP addressing
- STP and VTP
- Static and default routing
- Serial link configuration
- RIPv2, OSPF, and EIGRP
- Router-on-a-stick to MLS
- Standard and extended ACLs
- NAT configuration
- HSRP
Troubleshooting Scenarios:
These 30 labs present typical troubleshooting scenarios and require you to explore the misconfigured network, isolate the issues, and correct the problems. These are very complicated and realistic scenarios that truly test
your ability to perform the job of a network engineer. Topics covered include:
- Switch forwarding
- VLAN troubleshooting
- Path analysis and troubleshooting
- Port security
- STP
- Network discovery
- IP addressing and routing
- DHCP server troubleshooting
- NAT
- EIGRP and OSPF
- IPv6, MLS, and GRE tunnels
- Router-on-a-stick
System requirements:
Requires internet connection for product activation and updates.
Windows system requirements (minimum):
- Windows 10 (32/64-bit), Windows 8.1 (32/64-bit), or Windows 7 (32/64-bit)
- 1 gigahertz (GHz) or faster 32-bit (x86) or 64-bit (x64) processor
- 1 GB RAM (32-bit) or 2 GB RAM (64-bit)
- 16 GB available hard disk space (32-bit) or 20 GB (64-bit)
- DirectX 9 graphics device with WDDM 1.0 or higher driver
- Adobe Acrobat Reader version 8 and above
Mac system requirements (minimum):
- macOS 10.12, 10.11, or 10.10
- Intel core Duo 1.83 GHz
- 512 MB RAM (1 GB recommended)
- 1.5 GB hard disk space
- 32-bit color depth at 1024x768 resolution
- Adobe Acrobat Reader version 8 and above
Sean Wilkins (@Sean_R_Wilkins) is an accomplished networking consultant and writer for infoDispersion No. 1624 (www.infodispersion.com) who has been in the IT field for more than 20 years, working with several large enterprises. Sean holds certifications with Cisco (CCNP/CCDP), Microsoft (MCSE), and CompTIA (A+ and Network+). He spends most of his time writing articles and books for various clients, including Cisco Press, Pearson, Tom's IT Pro, and PluralSight, as well as being an active video training author for PluralSight. Sean maintains various online social media accounts, including Facebook (https: //www.facebook.com/ infoDispersion), Twitter (@Sean_R_Wilkins), and Linkedin (http: //www.linkedin.com/in/swilkins/en) and maintains a website for centrally organizing his content across multiple clients (http: //www.idisperse.info).
Wendell Odom, CCIE No. 1624, is the most respected author of Cisco networking books in the world. His books are known for their technical depth and accuracy. Wendell has worked as a network engineer, consultant, instructor, course developer, and book author, and he has produced videos, software, and blogs related to Cisco certifications. His website, with links to various study tools and resources, is at www.certskills.com.
